Rivet Sentence Examples

I'll teach you what to do and show you what kind of rivet to use.

The greatest care should be taken to see that all rivet holes are accurately punched, and if necessary that they are rhymed so that each rivet will have its full value.

The lieutenant explained how to rivet the hoof and went away to his own quarters.

Rivet bars tested on a gauge length eight times the diameter must have a tensile strength of 26 to 30 tons per sq.

Then using a ball pein hammer, form the end of the rivet by carefully hammering to mushroom it out.

Again, the physician as naturalist, though stimulated by the pathologist to delineate disease in its fuller manifestations, yet was hampered in a measure by the didactic method of constructing "types" which should command the attention of the disciple and rivet themselves on his memory; thus too often those incipient and transitory phases which initiate the paths of dissolution were missed.

It was in vain that the emperors tried to rivet the chains of the curia in this hereditary bondage, by attaching the small proprietor to his glebe, like the artisan to his gild and the soldier to his legion.

All you have to do is drill out the rivet that holds it in place and replace with the handily provided Allen bolt.

Some roofers have been known to once nail and tail rivet some slates on a roof.

Rivets The copper tail rivets The copper tail rivet located in the tail of a standard slate is normally located in the joint between the two lower slates.

The majority of the wind uplift load on the exposed section of the slate is transferred to the copper tail rivet.

The victims of this affliction lose for the time all self-control and all sense of their own identity, imitating the actions of any person who chances to rivet their attention.

Plates, angles and bars, other than rivet bars, must have a tensile strength of 28 to 32 tons per sq.

Instead, the joint should be made by pressing in the rivet pin.

Fairly simple to fit but you will need a drill and a rivet gun, alternatively some bicycle shops will fit them for you.

The tool is worked all around the edge of the rivet head, to drive the edge tightly onto the inner firebox.

Rivets The copper tail rivet located in the tail of a standard slate is normally located in the joint between the two lower slates.

Soft structured boarskin bags with rolled handles and gold rivet accents and hardware.

The good news is that you'll never lose a rivet.

Simply knowing the characters' names and having a brief understanding of the story is not enough to turn out an impressive script that will rivet viewers.

The bracing is accomplished by the introduction at the angles of the columns and girders or beams of gusset plates or knee braces, or by diagonal straps or rods properly attached by rivet or pin connexions.

It is attached to a brass disk E, which is fastened to the centre of the diaphragm F by means of a rivet, and is capable of moving to and fro like a plunger when the diaphragm vibrates.

In 1229 the Order began the conquest of Prussia, founding fortresses at each step to rivet its conquests (for instance, at Thorn, named after Toron in Palestine), much as the AngloNormans had done in their conquest of Wales.

Ancillon had convinced himself that the rigid class distinctions of the Prussian system were the philosophically ideal basis of the state, and that representation "by estates" was the only sound constitutional principle; his last and indeed only act of importance as minister was his collaboration with Metternich in the Vienna Final Act of the 12th of June 1834, the object of which was to rivet this system upon Germany for ever.

Rivet steel, which above all needs extreme ductility to endure the distortion of being driven home, and tube steel which must needs weld easily, no matter at what sacrifice of strength, are made as free from carbon, i.e.

Every nail driven should be as another rivet in the machine of the universe, you carrying on the work.

The methods of union adopted are not allowed to impair the strength of structures, which is calculated on the weakest sections through the rivet or bolt holes.

With medium or moderately hard steel all rivet holes should be drilled, or punched e in.